Talk:Copper units of pressure

Firearms Low‑importance

	This article is within the scope of WikiProject Firearms, a collaborative effort to improve the coverage of firearms on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.FirearmsWikipedia:WikiProject FirearmsTemplate:WikiProject FirearmsFirearms articles
Low	This article has been rated as Low-importance on the project's importance scale.

Science Low‑importance

	Science portal This article is within the scope of WikiProject Science, a collaborative effort to improve the coverage of Science on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.ScienceWikipedia:WikiProject ScienceTemplate:WikiProject Sciencescience articles
Low	This article has been rated as Low-importance on the project's importance scale.

units ?[edit]

'mPa' is used in the entry section, but 'MPa' is used in the 'comparing units' section. One is milli-Pascals, the other Mega-Pascals. Which is correct ?24.17.110.63 (talk) 15:30, 22 April 2008 (UTC)[reply]

Well, technically just "Pa" in the first section would be acceptable, but since it's always going to be a big number, I'll change it to MPa. scot (talk) 21:24, 22 April 2008 (UTC)[reply]

Invalid References[edit]

Note that I specifically refer to "cylinders", and am considering revolvers in the following offhand analysis.

None of the references listed in this article is adequate. Beyond that, essentially all of the info on this subject that can be found on the "net" is useless. Since gun manufacturers do not publish the yield points for their cylinders (or (easily determined, so I assume the test is done, but the data kept "in house"), published pressure data is only useful for "ballpark" estimation of relative peak stress produced in an adequately strong chamber.

For the record, cylinder strength data can be easily developed by attaching strain gages to an actual production cylinder, pressing a small metal plug in one end, filling the cylinder with silicone or urethane elastomer, and then compressing it with a properly fitted piston instrumented with a load cell. Test engineers will recognize what I am describing as an isostatic pressure test of hoop stress. Additional data would then be collected by testing a number of cylinders to failure and analyzing contributing factors to failure, performing followup low-cycle fatigue testing, and finally the determination of a safe limit. The data could then be used to evaluate strain data collected when the cylinder is used as designed in an actual gun frame (also instrumented to detect topstrap yield). — Preceding unsigned comment added by 208.127.3.249 (talk) 15:04, 13 May 2013 (UTC)[reply]

I don't believe the term "cylinder" in this article refers to revolver cylinders. In reference to copper or lead unit of pressure (CUP or LUP) "cylinder" refers to the cylinder of copper or lead crushed by the piston in the chamber of the test barrel. The amount of crush in these cylinders is then measured to determine the amount of pressure generated by firing the cartridge. -- Naaman Brown (talk) 14:32, 5 July 2018 (UTC)[reply]

External links modified[edit]

Hello fellow Wikipedians,

I have just modified one external link on Copper units of pressure. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

Added archive https://web.archive.org/web/20070928121135/http://www.handloads.com/misc/saami.htm to http://www.handloads.com/misc/saami.htm

When you have finished reviewing my changes, please set the checked parameter below to true or failed to let others know (documentation at {{Sourcecheck}}).

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 18 January 2022).

If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 16:38, 30 November 2016 (UTC)[reply]